Digiplex DGP-641 Manual de Instalação descarregar pdf (Página 55)

DGP-848 Control Panel 51

Figure 29 : Access Control Connections

2.0 PROGRAMMING

Programming the DGP2-641BL/RB keypad module is simple.

Enter Module Programming Mode, enter the desired section

followed by the required data. When programming the keypad, use

the keypad’s programming sheets (found in the Digiplex Series

Modules’ Programming Guide) to keep track of which sections

were programmed and how. We strongly recommend you read this

entire manual before you begin programming.

This module can also be programmed using the WinLoad Installer

Upload/Download Software. For more information, refer to the

WinLoad instructions or visit our Web site at www.paradox.ca.

2.1 Entering Module Programming Mode

The keypad, like all other modules in the system, is programmed

through the control panel. To do so, you must first enter Module

Programming Mode:

1) From Normal Mode press and hold the [0] key.

2) Enter the [

INSTALLER CODE] (by default 000000).

3) Enter section [953].

4) Enter the keypad’s 8-digit [SERIAL NUMBER].

5) Enter the 3-digit [

SECTION] you want to program.

6) Enter the required [

DATA].

The control panel will then redirect all programming to the selected

keypad. Every time the [

CLEAR] key is pressed it will revert to the

preceding step, unless entering in data in which case it will erase

the current data entry. Please note that the serial number is located

on the keypad's PC board or enter section [000] in Step 3 to view

the keypad’s serial number.

2.2 Programming Methods

The following methods can be used when programming the

keypad:

2.2.1 Feature Select Programming

Some sections are programmed by enabling or disabling options.

Within the sections, numbers from

[1]

[8]

represent a specific

keypad option. Press the key corresponding to the desired option and

the digit will appear in the display. This means the option is enabled.

Press the key again to remove the digit from the display thereby

disabling the option. Press

[

ENTER

]

when options are set.

2.2.2 Decimal Programming

Some sections require that a decimal value be entered. In this method,

any digit from 000 to 255 can be entered.

2.3 Module Broadcast

The control panel’s Module Broadcast feature can be used to copy

the contents of one keypad to one or many other keypads.

1) From Normal Mode press and hold the [0] key.

2) Enter [

INSTALLER CODE] (default: 000000).

3) Enter section [954].

4) Enter the [

SERIAL #] of the source keypad. The source is the

programmed keypad whose data you want to copy to other

keypads.

5) Enter the [

SERIAL #] of the destination keypads. The

destination is the keypad(s) you want to program with the

source’s data. If you want to program more than one keypad

with the source’s data, enter the serial numbers of the keypads

one at a time.

6) Once you have entered the serial numbers of the keypads you

want to program, press the [

ACC] key.

3.0 SYSTEM OPTIONS

3.1 Partition Assignment

SECTION [001]: OPTIONS [1] TO [4]

Keypads in the system can be assigned to one or more partitions.

Options [1] to [4] represent partitions 1 through 4 respectively. To

assign the keypad to a partition, enable the option that corresponds

to the desired partition. By default, partitions 1 to 4 are enabled.

3.2 Display Access Code Entry

SECTION [003]: OPTION [1]

The digits of the User Access Codes can be displayed on the LCD

screen when they are entered.

Option [1] OFF= Digits are replaced by a “*“ (default)

Option [1] ON = Access Code digits will be displayed

3.3 Display Exit Delay Timer

SECTION [003]: OPTION [2]

Based on the user's needs, an Exit Delay Timer will be

programmed to provide the user time to exit the partition before the

system is armed. The Exit Delay Timer's countdown can be

displayed on the LCD screen.

Option [2] OFF= Will not display Exit Delay timer (default)

Option [2] ON = LCD screen will display Exit Delay timer

DGP2-641RB DGP2-641RB

Fused external

power supply

(recommended)

Door Lock

IN4007

Diode

DGP2-641RB

Paradoor (460)

Request to Exit device.

Must be connected to

terminal.

If a door contact is not being used, install a jumper or a 1k

resistor across the

BLK and Z1 terminals depending on the control panel’s EOL definition.

If the REX (Request for Exit) device is not being used, place a jumper across

the BLK and Z2 terminals.

Door Contact

Must be connected

Z1 terminal.

* Follows control panel’s EOL definition.

No EOL

required

for

Z2.

1 2 ... 50 51 52 53 54 55 56 57 58 59 60 ... 67 68

Comentários a estes Manuais

Sem comentários

Digiplex DGP-641 Manual de Instalação Página 55

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Digiplex DGP-641